Heavy-duty armored chassis. Maximum protection, built like a tank.

Hard-edged chassis with faceted chamfer corners and standard side shoulder studs. Sharp and industrial.

Heroic muscle chassis with a raised armored chest and a sculpted six-block ab plate — three color zones to paint. Standard side shoulder studs.

Rounded two-part pod chassis — a wide oval drum over a smaller oval base. Soft, friendly, and clean for your own decals.

Clean-faced boxy chassis with chunky rounded edges — a blank canvas for your own decals. Built to Connection Standard v2.

Chamfer-edged chassis with a curved chest that rolls over into a flat top. Three color zones — front, sides and top/back. Built to Connection Standard v2.

Rounded spacesuit pod chassis wrapped in padded rib bands — matches the Astro legs. Body + accent color zones. Built to Connection Standard v2.

Soft-square chassis with a broad chest, a cinched belt band and flared hips. Three color zones — chest, belt and hips. Built to Connection Standard v2.

Six-sided chassis with a flat chest face and a heavy waist band. Two color zones — shell, and band/collar. Tapered arm pins, standard collar. Built to Connection Standard v2.

Chamfered two-part chassis — a clean chest over a flush lower section, split into upper (body) and lower (base) color zones. Tapered arm pins, tucked base collar. Built to Connection Standard v2.

Heroic V-taper chassis — a broad chamfered chest stepping down to a narrow waist, all one continuous octagonal shell. Two color zones, chest and lower body. Built to Connection Standard v2.

The chassis for the Buddy set — a soft pill shell wrapped by two ribbon bands with a brass chest stud. Three color zones: shell, ribbons and lower body. Built to Connection Standard v2.

Soft-cornered chassis built around a big ringed reactor port on the chest, with a raised shoulder yoke the arm pins emerge from and a flared lower section. Three color zones — shell, yoke and ring, and lower body — and the reactor core stays fire red. Built to Connection Standard v2.

Open-frame chassis — a chest block and a hip block bridged by four corner columns, so you can see straight through the waist, with a power core slung in the gap. Three color zones: chest, columns and hips. The core stays fire red. Built to Connection Standard v2.

The chassis cut to match the Scout head — a soft-cornered hull that swells across the shoulders and draws in toward the collar, with a dark plate sunk into the chest, three vent slits down each flank, and a raised spine running the length of the back. Built to Connection Standard v2.

Broad shoulders drawn down to a hard cinch and flared out again over the hips. A belt clamps the waist at its narrowest and a shield-shaped breastplate spreads across the chest, tapering to a point at the sternum. The hips wear a flared skirt that tucks back in above the collar. Three paintable zones: shell, belt and breastplate, and the skirt with the collar. Built to Connection Standard v2.

No outer shell at all — five armour plates threaded onto a spine, narrow at the waist and broadest across the chest and shoulders, with a vertebra closing every joint between them. Each vertebra is cut just inside the slimmer of the two plates it joins, so the joints step down with the silhouette instead of leaving gaps. Three colour zones: plates, spine and vertebrae, and the flared belt with the collar.

The chassis cut to match the Tube head — a soft-cornered cabinet with a slatted speaker grille set behind a one-piece bezel on the chest and two tuning dials below it, over a belted lower section. Three colour zones: cabinet, grille and dials, and the belt with the collar.

A soft-cornered chassis built around a bubble cockpit — a domed canopy sunk into a raised bezel on the chest, the same rimmed ring the Pal head wears over its ears and the Ring Knee carries at the joint. A belted lower section flares under it. Three colour zones: shell and bezel, canopy glass, and the belt with the collar.

The chassis cut to match the Armour Legs — a soft-cornered hull that swells at the chest and draws into a flared skirt, with the arm pins emerging from shoulder drums that carry the same proud rim over a sunken face as the knee drums. A pointed-oval lens is sunk into the chest to echo the ones on the knees. Three colour zones: hull, shoulder drums and chest lens, and the skirt with the collar. Built to Connection Standard v2.

The Reactor Frame shell with the chest port left off — a soft-cornered chassis in three clean tiers: a raised shoulder yoke the arm pins emerge from, a blank chest, and a flared lower section. Three color zones and nothing on the front, so your own decorations have the run of it. Built to Connection Standard v2.